Altera UG-01080 Betriebsanweisung Seite 96
- Seite / 484
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 5: 1G/10 Gbps Ethernet PHY IP Core 5–8
Data Interfaces
November 2012 Altera CorporationAltera Transceiver PHY IP Core
User Guide
Data Interfaces
Table 5–8 describes the signals in the XGMII and GMII interfaces. The MAC drives the
TX XGMII and GMII signals to the 1G/10GbE PHY. The 1G/10GbE PHY drives to the
RX XGMII or GMII signals to the MAC.
rx_clkout_1g
Output
GMII RX clock for the 1G RX parallel data source interface. The frequency is
125 MHz.
rx_clkout_10g
Output
XGMII RX clock for the 10G RX parallel data source interface. The frequency is
257.8125 MHz.
rx_coreclkin_1g
Input
Optional clock to drive the read side of the RX phase compensation FIFO in the
Standard PCS. The frequency is 125 MHz.
tx_coreclkin_1g
Input
Optional clock to drive the write side of the TX phase compensation FIFO in the
Standard PCS. The frequency is 125 MHz.
pll_ref_clk_1g
Input
TX PLL reference clock for the PMA block for the 1G mode. Its frequency is
125 or 62.5 MHz.
pll_ref_clk_10g
Input
TX PLL reference clock for the PMA block in 10G mode. Its frequency is
644.53125 or 322.265625 MHz.
pll_powerdown_1g
Input Resets the 1Gb TX PLLs.
pll_powerdown_10g
Input Resets the 10Gb TX PLLs.
tx_analogreset
Input Resets the analog TX portion of the transceiver PHY.
tx_digitalrest
Input Resets the digital TX portion of the transceiver PHY.
rx_analogreset
Input Resets the analog RX portion of the transceiver PHY.
rx_digitalreset
Input Resets the digital RX portion of the transceiver PHY.
usr_seq_reset
Input Not functional in 1G/10Gbe mode. Tie to 1’b0.
Table 5–7. Clock and Reset Signals (Part 2 of 2)
Signal Name Direction Description
Table 5–8. XGMII and GMII Signals (Part 1 of 2)
Signal Name Direction Description
1G/10GbE GMII Data Interface
xgmii_tx_dc_<n>[71:0]
Input
XGMII data and control for 8 lanes. Each lane consists of 8 bits of data and 1
bit of control.
xgmii_tx_clk
Input
Clock for SDR XGMII TX interface to the MAC. It should connect to
xgmii_rx_clk
. The frequency is 156.25 MHz.
xgmii_rx_dc_n[71:0]
Output
RX XGMII data and control for 8 lanes. Each lane consists of 8 bits of data and
1 bit of control.
xgmii_rx_clk
Output Clock for SDR XGMII RX interface to the MAC.The frequency is 156.25 MHz.
1G/10GbE GMII Data Interface
gmii_tx_d[7:0]
Input
TX data for 1G mode. Synchronized to
tx_clkout_1g
clock. The TX PCS
8B/10B module encodes this data which is sent to link partner.
gmii_rx_d[7:0]
Output
RX data for 1G mode. Synchronized to
rx_clkout_1g
clock. The RX PCS
8B/10B decoders decodes this data and sends it to the MAC.
gmii_tx_en
Input
When asserted, indicates the start of a new frame. It should remains asserted
until the last byte of data on the frame is present on
gmii_tx_d
.
- User Guide 1
- Contents 3
- Chapter 6. XAUI PHY IP Core 5
- Chapter 9. Custom PHY IP Core 6
- ContentsContents vii 7
- ContentsContents ix 9
- Additional Information 11
- 1. Introduction 13
- 1–2 Chapter 1: Introduction 14
- Avalon-MM PHY Management 15
- 1–4 Chapter 1: Introduction 16
- Chapter 1: Introduction 1–5 17
- Unsupported Features 18
- 2. Getting Started 19
- Specifying Parameters 20
- Simulate the IP Core 22
- 3. 10GBASE-R PHY IP Core 23
- 10GBASE-R protocol 24
- Arria V GT 10GBASE-R 25
- Transceiver Protocol 25
- General Option Parameters 29
- Interfaces 32
- Clocks for Arria V GT Devices 36
- Clocks for Arria V GZ Devices 37
- Clocks for Stratix IV Devices 37
- Clocks for Stratix V Devices 39
- 10GBASE-R PHY IP Core 47
- Note to Table 4–3: 51
- Speed Detection 54
- Functional Description 56
- Clock and Reset Interfaces 59
- SDR XGMII interface: 62
- Control and Status Interfaces 63
- PHY Link Training 64
- Daisy-Chain Mode 65
- 10GBASE-KR PHY 1GbE Registers 80
- Creating a 10GBASE-KR Design 83
- WAN Wide Area Network 87
- Acronym Definition 87
- 1G/10GbE Release Information 90
- 10GBASE-R Parameters 92
- 1Gb Ethernet Parameters 92
- 1G/10GbE Registers 100
- PMA Registers 101
- PCS Registers 102
- GMII PCS Registers 103
- Sequencer 106
- Cntl & 106
- Creating a 1G/10GbE Design 107
- Editing a MIF File 108
- Design Examples 109
- Dynamic Reconfiguration 110
- Simulation 111
- TimeQuest Timing Constraints 111
- Acronyms 111
- 6. XAUI PHY IP Core 113
- Release Information 114
- Device Family Support 114
- Devices 115
- Parameterizing the XAUI PHY 115
- General Parameters 116
- Analog Parameters 117
- Stratix IV Devices 118
- Advanced Options Parameters 119
- Configurations 120
- Data Interfaces 122
- SDR XGMII TX Interface 124
- SDR XGMII RX Interface 124
- XAUI Hard IP Core 125
- Hard PCS 125
- Soft PCS 125
- TimeQuest Timing Cons 135
- Interlaken PHY IP Core 137
- Optional Port Parameters 140
- Interfaces 141
- Avalon-ST TX Interface 142
- Avalon-ST RX Interface 144
- TX and RX Serial Interface 147
- PLL Interface 147
- Optional Clocks for Deskew 148
- Resource Utilization 154
- General Options Parameters 155
- s window for Gen1 or Gen2 160
- s window for Gen1 160
- Figure 8–4 illustrates the 162
- Optional Status Interface 163
- Serial Data Interface 164
- PHY IP Core for PCI Express 165
- Hard PCS and PMA 165
- Phase 2 (Optional) 170
- Phase 3 (Optional) 171
- 9. Custom PHY IP Core 175
- Custom PHY IP Core 176
- Stratix V FPGA 176
- Word Alignment Parameters 181
- Rate Match FIFO Parameters 182
- Byte Order Parameters 183
- SOP to a different byte lane 184
- IP Core 186
- Presets for Ethernet 187
- RX interface 190
- Clock Interface 191
- Custom PHY PCS and PMA 193
- 10. Low Latency PHY IP Core 199
- (PCS-PMA interface width) 202
- Additional Options Parameters 203
- PMA and Light-Weight PCS 210
- Auto-Negotiation 216
- Note to Figure11–2: 217
- Delay Estimation Logic 219
- Delay Numbers 220
- the number of bits 230
- Deterministic PHY IP Core 232
- Parameter Presets 241
- PMA Parameters 243
- TX PMA Parameters 244
- TX PLL<n> 245
- RX CDR Options 246
- PMA Optional Ports 246
- Standard PCS Parameters 249
- Phase Compensation FIFO 250
- Rate Match FIFO 253
- 10G PCS Parameters 257
- 10G TX FIFO 258
- Stratix V Devices 259
- 100 ppm 260
- Interlaken Frame Generator 262
- Interlaken Frame Synchronizer 263
- s period 265
- s period, the 265
- 64b/66b Encoder and Decoder 266
- 96-bit bound. It adds the 67 267
- Common Interface Ports 270
- Standard PCS Interface Ports 273
- 10G PCS Interface 276
- SDC Timing Constraints 284
- Simulation Support 286
- RX PMA Parameters 292
- Arria V Devices 299
- Cyclone V Devices 368
- Controller IP Core 379
- Altera V-Series FPGA 381
- 500 400 0 0 100 383
- 4.9152 Gbps 387
- Embedded 389
- Controller 389
- Offset Cancellation 390
- Duty Cycle Calibration 390
- PMA Analog Control Registers 391
- 7’h0C [6:0] RW 391
- EyeQ Registers 392
- DFE Registers 394
- (Part 1 of 2) 395
- address to 0x0 396
- (Part 2 of 2) 396
- address of 0xB 397
- AEQ Registers 399
- ATX PLL Calibration Registers 400
- PLL Reconfiguration 401
- Transceiver PHYs 402
- PLL Reconfiguration Registers 403
- 7’h44 [15:0] RW 403
- Channel Reconfiguration 405
- Streamer Module Registers 406
- register address is invalid 406
- When the 407
- register specifies a 407
- register. When 407
- register 408
- MIF Generation 409
- MIF Format 410
- Arguments: 412
- -h: Displays help 412
- Reduced MIF Creation 413
- Register-Based Write 414
- Register-Based Read 415
- Figure 16–6. Sample MIF 418
- Example 16–11. (continued) 419
- Loopback Modes 427
- Transceiver 428
- Transceiver PHY Instance 429
- Transceiver PHY 429
- Reset Controller 429
- Assignments 437
- register to enable the 455
- Transceivers 456
- Stratix V GX/GS devices 458
- Note to Table 19–3: 459
- Note to Table 19–5: 462
- Note to Table 19–7: 465
- Revision History 468
- s for Gen2 operation 476
- address 480
- Note to Table: 482
- Typographic Conventions 483
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern