Altera Serial Digital Interface (SDI) MegaCore Function Bedienungsanleitung Seite 7
- Seite / 140
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
February 2013 Altera Corporation Serial Digital Interface (SDI) MegaCore Function
User Guide
1. About This MegaCore Function
This user guide describes the Altera
®
Serial Digital Interface (SDI) MegaCore
®
function and the accompanying SDI Audio IP cores.
The SDI MegaCore function implements a receiver, transmitter, or full-duplex SDI at
standard definition (SD), high definition (HD), or 3 gigabits per second (3G). The SDI
MegaCore function also supports dual standard (HD-SDI and SD-SDI) and triple
standard (SD-SDI, HD-SDI, and 3G-SDI). These modes provide automatic receiver
rate detection.
You can instantiate the SDI Audio IP cores with the SDI MegaCore function.
1 For more information about the SDI Audio cores, refer to “SDI Audio IP Cores” on
page 4–1.
Features
Table 1–1 lists the features of the SDI MegaCore function.
Table 1–1. SDI MegaCore Function Features
Feature Description
Support
■ Multiple SDI standards and video formats (refer to Table 1–5 and Table 1–6)
■ RP168 video switch line requirement
■ OpenCore Plus evaluation
Transmitter
■ Cyclical redundancy check (CRC) encoding (HD only)
■ Line number (LN) insertion (HD only)
■ Word scrambling
■ Transmitter clock multiplexer (optional)
Receiver
■ CRC decoding (HD only)
■ LN extraction (HD only)
■ Framing and extraction of video timing signals
■ Word alignment and descrambling
MegaWizard™ Plug-In Manager
■ Easy-to-use parameter editor
IP functional simulation models ■ Use in Altera-supported VHDL and Verilog HDL simulators
- User Guide 1
- Contents 3
- Chapter 4. SDI Audio IP Cores 4
- Appendix A. Constraints 5
- Appendix B. Clocking 5
- Features 7
- Release Information 8
- Device Family Support 8
- General Description 9
- Notes to Table 1–5: 10
- OpenCore Plus Evaluation 11
- Resource Utilization 12
- 2. Getting Started 15
- Design Flow 16
- SDI Walkthrough 17
- Parameterizing 19
- Setting Up Simulation 20
- Generating Files 20
- - SD 270 Mbps 22
- - HD 1.485 Gbps 22
- - 3G 2.97 Gbps 22
- Simulating the Design 23
- Specifying Constraints 25
- Multiple Channels 26
- Compiling the Design 28
- Programming a Device 28
- Setting Up Licensing 29
- 3. Functional Description 31
- Block Description 32
- HD-SDI LN Insertion 34
- Scrambling and NRZI Coding 35
- Transceiver Clock 35
- Receiver 36
- Word Alignment 38
- Video Timing Flags Extraction 39
- RP168 Switching Compliance 39
- HD-SDI LN Extraction 40
- HD-SDI CRC Checking 40
- Accessing Transceiver 40
- Transmitter 42
- Transmitter Clocks 42
- Receiver Clocks 43
- Notes to Table 3–5: 44
- Notes to Figure 3–8: 44
- Figure 3–9. Receiver Clocks 46
- rxdata 47
- Note to Table 3–7: 50
- Notes to Figure 3–11: 51
- Figure 3–12. Receiver Clocks 53
- New TRS reasserts 55
- Stratix IV GX 57
- Note to Table 3–10: 58
- Note to Table 3–11: 58
- Notes to Figure 3–18: 60
- Note to Figure 3–19: 61
- User Logic 62
- Encrypted SDI IP Core 62
- Cyclone IV GX 63
- Notes to Table 3–12: 70
- Note to Table 3–13: 70
- Note to Table 3–14: 71
- Note to Figure 3–30: 77
- Notes to Figure 3–33: 78
- signal in 82
- Table 3–18 on page 3–50 82
- Notes to Figure 3–40: 83
- Notes to Table 3–19: 85
- MegaCore Verification 87
- 4. SDI Audio IP Cores 89
- Functional Description 90
- Note to Table 4–4: 93
- Note to Table 4–5: 94
- MegaCore function 100
- Register Maps 103
- Parameters 105
- AES Format 109
- Avalon-ST Audio Interface 109
- Note to Figure 4–6: 110
- Instantiating the IP Cores 111
- Simulating the Testbench 112
- Design Example 113
- Components 114
- Hardware Setup 116
- D6 D7 D8 D9 D10 D11 D12 D13 118
- A. Constraints 123
- Notes to Figure A–1: 124
- (gxb_rxclk 125
- Specify Clock Characteristics 126
- Set Multicycle Paths 127
- 337.5-MHz Zero-degree Clocks 128
- Minimize Timing Skew 129
- Non Cyclone Devices 130
- Cyclone Devices Only 131
- A–10 Appendix A: Constraints 132
- B. Clocking 133
- B–2 Appendix B: Clocking 134
- C. Receive and Retransmit 135
- Loopback FIFO Buffer 136
- Additional Information 137
- Info–2 Additional Information 138
- Document Revision History 138
- How to Contact Altera 139
- Typographic Conventions 139
- Info–4 Additional Information 140
Verwandte Produkte und Handbücher für Messgeräte Altera Serial Digital Interface (SDI) MegaCore Function
(44 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern