Altera Serial Digital Interface (SDI) MegaCore Function Bedienungsanleitung Seite 65
- Seite / 140
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 3: Functional Description 3–35
Block Description
February 2013 Altera Corporation Serial Digital Interface (SDI) MegaCore Function
User Guide
ALTPLL_RECONFIG Connections
Figure 3–21 shows the handshaking between the SDI MegaCore function and the
reconfig control logic, and the expected output of some of the
ALTPLL_RECONFIG
signals.
The following sequence of events occur for handshaking to the reconfiguration logic:
1. The SDI MegaCore function sets
rx_std[1:0]
to the desired video standard. This
action is performed as part of the video standards detection algorithm.
2. The SDI MegaCore function asserts
SDI_START_RECONFIG
to make a
reconfiguration request.
3. The reconfig control logic sets
WRITE_FROM_ROM
line to 1, and signals the
ALTPLL_RECONFIG megafunction to write from the ROM.
4. The reconfig control logic asserts the
PLL_RECONFIG
line to 1, and signals the
ALTPLL_RECONFIG megafunction to start the reconfiguration process.
5. When the reconfiguration has been performed, the transceiver’s PLL asserts the
output signal,
PLL_SCANDONE
, to the ALTPLL_RECONFIG megafunction indicating
that the PLL is reconfigured, and internally indicates to the SDI MegaCore
function to start locking to the incoming data.
6. The SDI MegaCore function sets the
SDI_START_RECONFIG
line to 0 to indicate that
the request is completed and acknowledged.
Figure 3–23. Handshaking between SDI MegaCore Function and ALTPLL_RECONFIG Signals
SDI_START_RECONFIG
RX_STD[1:0]
11 01
PLL_ARESET
PLL_CONFIGUPDATE
PLL_SCANCLK
PLL_SCANCLKENA
PLL_SCANDATA
PLL_SCANDATAOUT
PLL_SCANDONE
PLL_RECONFIG
RESET_ROM_ADDRESS
ROM_DATA_IN
WRITE_FROM_ROM
BUSY
WRITE_ROM_ENA
ROM_ADDRESS_OUT
2
34 5
61
- User Guide 1
- Contents 3
- Chapter 4. SDI Audio IP Cores 4
- Appendix A. Constraints 5
- Appendix B. Clocking 5
- Features 7
- Release Information 8
- Device Family Support 8
- General Description 9
- Notes to Table 1–5: 10
- OpenCore Plus Evaluation 11
- Resource Utilization 12
- 2. Getting Started 15
- Design Flow 16
- SDI Walkthrough 17
- Parameterizing 19
- Setting Up Simulation 20
- Generating Files 20
- - SD 270 Mbps 22
- - HD 1.485 Gbps 22
- - 3G 2.97 Gbps 22
- Simulating the Design 23
- Specifying Constraints 25
- Multiple Channels 26
- Compiling the Design 28
- Programming a Device 28
- Setting Up Licensing 29
- 3. Functional Description 31
- Block Description 32
- HD-SDI LN Insertion 34
- Scrambling and NRZI Coding 35
- Transceiver Clock 35
- Receiver 36
- Word Alignment 38
- Video Timing Flags Extraction 39
- RP168 Switching Compliance 39
- HD-SDI LN Extraction 40
- HD-SDI CRC Checking 40
- Accessing Transceiver 40
- Transmitter 42
- Transmitter Clocks 42
- Receiver Clocks 43
- Notes to Table 3–5: 44
- Notes to Figure 3–8: 44
- Figure 3–9. Receiver Clocks 46
- rxdata 47
- Note to Table 3–7: 50
- Notes to Figure 3–11: 51
- Figure 3–12. Receiver Clocks 53
- New TRS reasserts 55
- Stratix IV GX 57
- Note to Table 3–10: 58
- Note to Table 3–11: 58
- Notes to Figure 3–18: 60
- Note to Figure 3–19: 61
- User Logic 62
- Encrypted SDI IP Core 62
- Cyclone IV GX 63
- Notes to Table 3–12: 70
- Note to Table 3–13: 70
- Note to Table 3–14: 71
- Note to Figure 3–30: 77
- Notes to Figure 3–33: 78
- signal in 82
- Table 3–18 on page 3–50 82
- Notes to Figure 3–40: 83
- Notes to Table 3–19: 85
- MegaCore Verification 87
- 4. SDI Audio IP Cores 89
- Functional Description 90
- Note to Table 4–4: 93
- Note to Table 4–5: 94
- MegaCore function 100
- Register Maps 103
- Parameters 105
- AES Format 109
- Avalon-ST Audio Interface 109
- Note to Figure 4–6: 110
- Instantiating the IP Cores 111
- Simulating the Testbench 112
- Design Example 113
- Components 114
- Hardware Setup 116
- D6 D7 D8 D9 D10 D11 D12 D13 118
- A. Constraints 123
- Notes to Figure A–1: 124
- (gxb_rxclk 125
- Specify Clock Characteristics 126
- Set Multicycle Paths 127
- 337.5-MHz Zero-degree Clocks 128
- Minimize Timing Skew 129
- Non Cyclone Devices 130
- Cyclone Devices Only 131
- A–10 Appendix A: Constraints 132
- B. Clocking 133
- B–2 Appendix B: Clocking 134
- C. Receive and Retransmit 135
- Loopback FIFO Buffer 136
- Additional Information 137
- Info–2 Additional Information 138
- Document Revision History 138
- How to Contact Altera 139
- Typographic Conventions 139
- Info–4 Additional Information 140
Verwandte Produkte und Handbücher für Messgeräte Altera Serial Digital Interface (SDI) MegaCore Function
(44 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern