Altera RapidIO II MegaCore Function Bedienungsanleitung Seite 205
- Seite / 218
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 7: Testbench 7–11
Transceiver Level Connections in the Testbench
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
Transceiver Level Connections in the Testbench
The testbench for Arria 10 variations demonstrates one method to connect the reset
controller, the TX PLL, and the RapidIO II IP core to each other.
Figure 7–2. RapidIO II IP Core, TX PLL, and Reset Controller Connections in Arria 10 Testbench
Reset Controller
TX
PLL
Transmitter
(Native PHY)
Receiver
(Native PHY)
pll_refclk0
tx_bonding_clocks
tx_analogreset
tx_digitalreset
tx_cal_busy
rx_analogreset
rx_digitalreset
rx_is_lockedtodata
rx_cal_busy
tx_pll_refclk
reset
pll_locked
RapidIO II IP Core
tx_ready
pll_powerdown
mcg_reset
rx_ready
reference
clock
Table 7–6. External Transceiver TX PLL Connections to RapidIO II IP Core
Signal Direction Connection Requirements
pll_powerdown
Input
Connect
pll_powerdown
to the
pll_powerdown[0]
output port of the reset controller.
pll_refclk0
Input
Drive the PLL
pll_refclk0
input port and the RapidIO II
IP core
tx_pll_refclk
signal from the same clock
source.
pll_locked
Output
Connect
pll_locked
to the
pll_locked[n]
input signal
of the reset controller, for each transceiver channel n that
connects to the RapidIO link.
pll_cal_busy
Output
Drive the
pll_tx_cal_busy
input signal of the reset
controller.
mcgb_rst
Input Drive
mcgb_rst
from the system reset signal.
tx_bonding_clocks
[6N-1:0]
where N is the number
of lanes in the IP core
variation
Ouput
Connect the TX PLL tx_bonding_clocks ouput signal bits
[6z+5:6z] to the RapidIO II IP core
tx_bonding_clocks_chz
input signal to RapidIO lane z.
- User Guide 1
- RapidIO II MegaCore Function 1
- Contents 3
- Contents v 5
- Chapter 5. Signals 6
- Chapter 6. Software Interface 6
- Chapter 7. Testbench 6
- 1. About The RapidIO II 9
- MegaCore Function 9
- Releases 10
- RapidIO II IP Core Features 10
- Features 11
- Device Family Support 12
- IP Core Verification 13
- Hardware Testing 14
- Interoperability Testing 14
- Note to Table 1–3: 16
- Notes to Table 1–4: 16
- Installation and Licensing 17
- 2. Getting Started 19
- Simulating IP Cores 22
- Transceiver Settings 26
- External Transceiver PLL 26
- 3. Parameter Settings 31
- Note to Table 3–1: 32
- Enable 16-Bit Device ID Width 33
- Logical Layer Settings 34
- Capability Registers Settings 35
- Device ID 36
- Vendor ID 36
- Revision ID 36
- Assembly ID 36
- Assembly Information CAR 37
- Enable Flow Control Support 38
- Enable Switch Support 38
- Number of Ports 38
- Port Number 39
- Maximum PDU 39
- Destination Operations CAR 40
- Port General Control CSR 40
- Port 0 Control CSR 41
- Lane n Status 0 CSR 41
- Extended Features Pointer CSR 41
- 4. Functional Description 43
- Note to Table 4–2: 44
- Clocking and Reset Structure 45
- Notes to Table 4–3: 46
- RapidIO II 47
- Transactions 55
- Notes to Table 4–6: 57
- Notes to Table 4–7: 59
- Note to Table 4–8: 59
- Note to Figure 4–9: 66
- Note to Table 4–10: 70
- Notes to Table 4–11: 71
- Table 6–60 on page 6–40 72
- Note to Table 4–12: 73
- Maintenance Module 74
- Maintenance Interface Signals 75
- Doorbell Module Block Diagram 86
- Preserving Transaction Order 87
- Doorbell Module Signals 88
- Generating a Doorbell Message 88
- Receiving a Doorbell Message 89
- Transaction ID Ranges 90
- Notes to Table 4–24: 92
- Note to Table 4–26: 94
- Note to Table 4–27: 95
- field 97
- User Receiving Write Request 100
- Logical Layer Interfaces 101
- Transport Layer 112
- Receiver 113
- Transmitter 114
- Physical Layer 115
- Physical Layer Interfaces 116
- Low-level Interface Receiver 116
- CRC Checking and Removal 117
- Protocol Violations 119
- Fatal Errors 119
- Maintenance Avalon-MM Slave 120
- Maintenance Avalon-MM Master 121
- Port-Write Reception Module 122
- Input/Output Avalon-MM Slave 122
- Input/Output Avalon-MM Master 123
- 5. Signals 125
- Physical Layer Signals 126
- Low Latency Signals 127
- Multicast Event Signals 128
- Chapter 5: Signals 5–5 129
- Note to Table 5–7: 130
- Chapter 5: Signals 5–7 131
- 5–8 Chapter 5: Signals 132
- Register-Related Signals 133
- Avalon-MM Interface Signals 133
- Note to Table 5–12: 134
- Chapter 5: Signals 5–11 135
- Note to Table 5–15: 136
- Error Reporting Signals 137
- 5–14 Chapter 5: Signals 138
- 6. Software Interface 139
- Memory Map 140
- Physical Layer Registers 144
- Note to Table 6–9: 147
- Note to Table 6–14: 154
- Note to Table 6–15: 158
- Note to Table 6–17: 160
- Note to Table 6–22: 164
- Note to Table 6–23: 164
- Note to Table 6–24: 165
- Note to Table 6–25: 165
- Note to Table 6–26: 166
- Note to Table 6–27: 167
- Notes to Table 6–28: 168
- Notes to Table 6–29: 169
- Note to Table 6–30: 169
- Note to Table 6–31: 169
- Notes to Table 6–32: 170
- Note to Table 6–34: 171
- Note to Table 6–35: 171
- Note to Table 6–36: 172
- Note to Table 6–37: 172
- Transmit Port-Write Registers 174
- Receive Port-Write Registers 175
- Note to Table 6–59: 178
- Error Management Registers 180
- Note to Table 6–66: 181
- Notes to Table 6–67: 183
- Notes to Table 6–70: 185
- Notes to Table 6–71: 185
- Doorbell Message Registers 191
- Note to Table 6–89: 193
- 7. Testbench 195
- 7–2 Chapter 7: Testbench 196
- Testbench Overview 196
- Testbench Sequence 197
- 7–4 Chapter 7: Testbench 198
- Chapter 7: Testbench 7–5 199
- SWRITE Transactions 200
- NREAD Transactions 200
- NWRITE_R Transactions 201
- NWRITE Transactions 202
- Doorbell Transactions 202
- Port-Write Transactions 203
- Testbench Completion 204
- Chapter 7: Testbench 7–11 205
- 7–12 Chapter 7: Testbench 206
- A. Initialization Sequence 207
- MegaCore Function v12.1 209
- Additional Information 213
- Info–2 Additional Information 214
- Document Revision History 214
- Additional Information Info–3 215
- Info–4 Additional Information 216
- Note to Table: 217
- Info–6 Additional Information 218
- Typographic Conventions 218
Verwandte Produkte und Handbücher für Messgeräte Altera RapidIO II MegaCore Function
(198 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern