Altera RapidIO II MegaCore Function Bedienungsanleitung Seite 147
- Seite / 218
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 6: Software Interface 6–9
Physical Layer Registers
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
DISCOVER
[29] RW
This device has been located by the processing element responsible for system
configuration.
1'b0 - The device has not been previously discovered
1'b1 - The device has been discovered by another processing element
This field is for software use only. Its value has no effect on hardware.
(1)
RSRV
[28:0] RO Reserved 29'b0
Note to Table 6–9:
(1) The reset value of this field is set in the RapidIO II parameter editor.
Table 6–9. Port General Control—Offset: 0x13C (Part 2 of 2)
Field Bits Access Function Default
Table 6–10. Port 0 Link Maintenance Request CSR—Offset: 0x140
Field Bits Access Function Default
RSRV
[31:3] RO Reserved 29'b0
COMMAND
[2:0] RW
Command to be sent in a
link-request
control symbol. When a
valid value is written to this field, the RapidIO II IP core generates a
link-request
control symbol with the specified command. The IP
core does not generate a
link-request
control symbol when an
invalid value is written.
The following values are valid:
3’b011: reset-device
3’b100: input-status
3'b000
Table 6–11. Port 0 Link Maintenance Response CSR—Offset: 0x144
Field Bits Access Function Default
RESPONSE_VALID
[31] RO,RC
Value is the status of the most recent
link-request
control symbol
this RapidIO II IP core sent on the RapidIO link. If the
link-request
control symbol is a
link-request input-status
control symbol,
this bit, if set, indicates that the
link-response
control symbol has
been received and the status fields in this register are valid. If the
link-request
control symbol is a
link-request reset-device
control symbol, this bit, if set, indicates that the
link-request
was
transmitted.
This bit automatically clears in response to a read operation.
1’b0
RSRV
[30:11] RO Reserved 20’b0
ACKID_STATUS
[10:5] RO
Value of the
ackID_status
field in the
link-response
control
symbol. This field holds the value of the next expected ackID. Refer to
Table 3-3 in the RapidIO Interconnect Specification v2.2 Part 6:
LP-Serial Physical Layer Specification.
6'b0
PORT_STATUS
[4:0] RO
Value of the
port-status
field in the
link-response
control
symbol. Refer to Table 3-6 in the RapidIO Interconnect Specification
v2.2 Part 6: LP-Serial Physical Layer Specification.
5'b0
- User Guide 1
- RapidIO II MegaCore Function 1
- Contents 3
- Contents v 5
- Chapter 5. Signals 6
- Chapter 6. Software Interface 6
- Chapter 7. Testbench 6
- 1. About The RapidIO II 9
- MegaCore Function 9
- Releases 10
- RapidIO II IP Core Features 10
- Features 11
- Device Family Support 12
- IP Core Verification 13
- Hardware Testing 14
- Interoperability Testing 14
- Note to Table 1–3: 16
- Notes to Table 1–4: 16
- Installation and Licensing 17
- 2. Getting Started 19
- Simulating IP Cores 22
- Transceiver Settings 26
- External Transceiver PLL 26
- 3. Parameter Settings 31
- Note to Table 3–1: 32
- Enable 16-Bit Device ID Width 33
- Logical Layer Settings 34
- Capability Registers Settings 35
- Device ID 36
- Vendor ID 36
- Revision ID 36
- Assembly ID 36
- Assembly Information CAR 37
- Enable Flow Control Support 38
- Enable Switch Support 38
- Number of Ports 38
- Port Number 39
- Maximum PDU 39
- Destination Operations CAR 40
- Port General Control CSR 40
- Port 0 Control CSR 41
- Lane n Status 0 CSR 41
- Extended Features Pointer CSR 41
- 4. Functional Description 43
- Note to Table 4–2: 44
- Clocking and Reset Structure 45
- Notes to Table 4–3: 46
- RapidIO II 47
- Transactions 55
- Notes to Table 4–6: 57
- Notes to Table 4–7: 59
- Note to Table 4–8: 59
- Note to Figure 4–9: 66
- Note to Table 4–10: 70
- Notes to Table 4–11: 71
- Table 6–60 on page 6–40 72
- Note to Table 4–12: 73
- Maintenance Module 74
- Maintenance Interface Signals 75
- Doorbell Module Block Diagram 86
- Preserving Transaction Order 87
- Doorbell Module Signals 88
- Generating a Doorbell Message 88
- Receiving a Doorbell Message 89
- Transaction ID Ranges 90
- Notes to Table 4–24: 92
- Note to Table 4–26: 94
- Note to Table 4–27: 95
- field 97
- User Receiving Write Request 100
- Logical Layer Interfaces 101
- Transport Layer 112
- Receiver 113
- Transmitter 114
- Physical Layer 115
- Physical Layer Interfaces 116
- Low-level Interface Receiver 116
- CRC Checking and Removal 117
- Protocol Violations 119
- Fatal Errors 119
- Maintenance Avalon-MM Slave 120
- Maintenance Avalon-MM Master 121
- Port-Write Reception Module 122
- Input/Output Avalon-MM Slave 122
- Input/Output Avalon-MM Master 123
- 5. Signals 125
- Physical Layer Signals 126
- Low Latency Signals 127
- Multicast Event Signals 128
- Chapter 5: Signals 5–5 129
- Note to Table 5–7: 130
- Chapter 5: Signals 5–7 131
- 5–8 Chapter 5: Signals 132
- Register-Related Signals 133
- Avalon-MM Interface Signals 133
- Note to Table 5–12: 134
- Chapter 5: Signals 5–11 135
- Note to Table 5–15: 136
- Error Reporting Signals 137
- 5–14 Chapter 5: Signals 138
- 6. Software Interface 139
- Memory Map 140
- Physical Layer Registers 144
- Note to Table 6–9: 147
- Note to Table 6–14: 154
- Note to Table 6–15: 158
- Note to Table 6–17: 160
- Note to Table 6–22: 164
- Note to Table 6–23: 164
- Note to Table 6–24: 165
- Note to Table 6–25: 165
- Note to Table 6–26: 166
- Note to Table 6–27: 167
- Notes to Table 6–28: 168
- Notes to Table 6–29: 169
- Note to Table 6–30: 169
- Note to Table 6–31: 169
- Notes to Table 6–32: 170
- Note to Table 6–34: 171
- Note to Table 6–35: 171
- Note to Table 6–36: 172
- Note to Table 6–37: 172
- Transmit Port-Write Registers 174
- Receive Port-Write Registers 175
- Note to Table 6–59: 178
- Error Management Registers 180
- Note to Table 6–66: 181
- Notes to Table 6–67: 183
- Notes to Table 6–70: 185
- Notes to Table 6–71: 185
- Doorbell Message Registers 191
- Note to Table 6–89: 193
- 7. Testbench 195
- 7–2 Chapter 7: Testbench 196
- Testbench Overview 196
- Testbench Sequence 197
- 7–4 Chapter 7: Testbench 198
- Chapter 7: Testbench 7–5 199
- SWRITE Transactions 200
- NREAD Transactions 200
- NWRITE_R Transactions 201
- NWRITE Transactions 202
- Doorbell Transactions 202
- Port-Write Transactions 203
- Testbench Completion 204
- Chapter 7: Testbench 7–11 205
- 7–12 Chapter 7: Testbench 206
- A. Initialization Sequence 207
- MegaCore Function v12.1 209
- Additional Information 213
- Info–2 Additional Information 214
- Document Revision History 214
- Additional Information Info–3 215
- Info–4 Additional Information 216
- Note to Table: 217
- Info–6 Additional Information 218
- Typographic Conventions 218
Verwandte Produkte und Handbücher für Messgeräte Altera RapidIO II MegaCore Function
(198 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern