Altera 10-Gbps Ethernet MAC MegaCore Function Bedienungsanleitung Seite 41
- Seite / 175
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 4: 10GbE MAC with IEEE1588v2 Design Example 4–3
10GbE with IEEE 1588v2 Design Example Components
February 2014 Altera Corporation 10-Gbps Ethernet MAC MegaCore Function User Guide
The 10GbE with IEEE 1588v2 design example comprises the following components:
■ Altera Ethernet 10G design example—the default 10G design example that has the
following settings:
■ 10GbE Ethernet MAC—the MAC IP core with IEEE 1588v2 option enabled.
■ 10GBASE-R PHY—the PHY IP core with IEEE 1588v2 option enabled.
■ Ethernet Loopback—the loopback module provides a mechanism for you to
verify the functionality of the MAC and PHY.
■ MDIO and FIFO features turned off.
■ Transceiver Reconfiguration Controller—dynamically calibrates and reconfigures
the features of the PHY IP cores.
■ Ethernet Packet Classifier—decodes the packet type of incoming PTP packets and
returns the decoded information to the 10GbE Ethernet MAC.
■ Ethernet Time-of-Day (ToD) Clock—provides 64-bits and/or 96-bits time-of-day to
TX and RX of 10GbE Ethernet MAC.
■ Pulse Per Second Module—returns pulse per second (pps) to user.
■ Avalon MM Master Translator—provides access to the registers of the following
components through the Avalon-MM interface:
■ MAC and Ethernet Loopback
■ Transceiver Reconfiguration Controller
■ ToD
f For more information about ToD clock, refer to Appendix B, Time-of-Day (ToD)
Clock; and for more information about Packet Classifier, refer to Appendix C, Packet
Classifier.
4.2.1. Base Addresses
Table 4–1 lists the design example components that you can reconfigure to suit your
verification objectives. To reconfigure the components, write to their registers using
the base addresses listed in the table and the register offsets described in the
components' user guides.
1 This design example uses a 19-bit width address bus to access the base address of
components other than the MAC.
Table 4–1. Base Addresses of 10GbE with IEEE 1588v2 Design Example Components
Component Base Address
MAC and Ethernet Loopback 0x00000
Transceiver Reconfiguration Controller 0x80400
Time of Day Clock 0x81000
- User Guide 1
- Contents 3
- Contents iv 4
- Chapter 8. Registers 5
- Chapter 9. Interface Signals 5
- 1. About This IP Core 7
- 1.2. Release Information 8
- 1.3. Device Family Support 9
- 1.4. IP Core Verification 10
- ■ Timestamping is enabled 12
- ■ ptp_1step is disabled 12
- 2.2. Design Flows 14
- 2.3.2. Simulate the IP Core 15
- 2.4.1. Specify Parameters 16
- 2.4.3. Simulate the System 17
- [1] register bit to 1 18
- 3. 10GbE MAC Design Examples 19
- 3.2.0.2. Base Addresses 22
- Table 3–5 on page 3–10 23
- Creating a New 10GbE Design 24
- 3.6. 10GbE Testbenches 26
- 3.6.3. 10GbE Testbench Files 27
- 10GbE Testbenches 28
- Notes to Table 3–6: 36
- 4.1. Software Requirements 39
- Altera FPGA 40
- Design Example 40
- 4.2.1. Base Addresses 41
- Figure 4–3. Testbench 43
- The <ip 44
- Simulator 45
- 5.2.2. Base Addresses 49
- 1G/10GbE Design Example Files 50
- 5.5. 1G/10GbE Testbench 51
- Testbench 52
- 1G/10GbE Testbench 53
- 5.5.4.2. Backplane-KR Mode 55
- 6.2.1. Base Addresses 62
- ModelSim Simulator 66
- 7. Functional Description 68
- Architecture 69
- 7.2. Interfaces 70
- 7.2.2. SDR XGMII 71
- 7.2.3. GMII 71
- 7.2.4. MII 71
- 7.3. Frame Types 72
- 7.4. Transmit Datapath 72
- 7.4.2. Address Insertion 73
- Note to Figure 7–5: 74
- 7.4.4. XGMII Encapsulation 75
- 7.4.6. SDR XGMII Transmission 76
- Figure 7–7. Endian Conversion 77
- 7.5. Receive Datapath 78
- 7.5.4. Address Checking 79
- 7.5.5. Frame Type Checking 79
- 7.5.6. Length Checking 80
- 7.5.7. CRC-32 and Pad Removal 81
- 7.5.8. Overflow Handling 82
- Congestion and Flow Control 83
- 7.7.2.1. PFC Frame Reception 86
- Figure 7–11. Fault Signaling 87
- 7.9. IEEE 1588v2 88
- IEEE 1588v2 89
- 7.9.1. Architecture 90
- 7.9.2. Transmit Datapath 91
- 7.9.3. Receive Datapath 92
- 7.9.4. Frame Format 92
- MAC Header 93
- Note to Figure 7–16: 94
- 8. Registers 95
- 8.1. MAC Registers 96
- 0x0C1. Bits 4 to 31 are 98
- 0x0C3. Bits 4 to 31 are 98
- Register Name Access 100
- Bits 4 to 31 are reserved 101
- register 111
- Name R/W Description 112
- 8.3. Register Initialization 113
- 8–20 Chapter 8: Registers 114
- Register Initialization 114
- Chapter 8: Registers 8–21 115
- 8–22 Chapter 8: Registers 116
- Chapter 8: Registers 8–23 117
- 8–24 Chapter 8: Registers 118
- Chapter 8: Registers 8–25 119
- 9. Interface Signals 120
- Note to Table 9–1: 121
- Note to Figure 9–2: 123
- Note to Figure 9–3: 123
- Notes to Figure 9–4: 124
- Note to Figure 9–5: 125
- 9.0.3. SDR XGMII 127
- Note to Figure 9–7: 128
- Note to Figure 9–8: 129
- 9.0.4. GMII Signals 130
- 9.0.5. MII Signals 130
- Note to Table 9–8: 136
- Note to Table 9–9: 139
- 1588v2 feature 142
- 10. Design Considerations 150
- 10GbE MAC XAUI/10G BASE-R PHY 151
- Reconfiguration Controller 151
- A. Frame Format 153
- Figure A–2. VLAN Frame Format 154
- A.3. Pause Frame 155
- Figure A–5. PFC Frame Format 156
- B. Time-of-Day (ToD) Clock 157
- B.4. Parameter Setting 158
- ■ Bits 20 to 31: Not used 160
- B.6.1. Adjusting ToD’s Drift 161
- C. Packet Classifier 162
- Classifier 163
- D. ToD Synchronizer 166
- D.2. Block Diagram 167
- D.4. ToD Synchronizer Signals 169
- Additional Information 171
- Info–2 Additional Information 172
- Document Revision History 172
- Additional Information Info–3 173
- How to Contact Altera 174
- Typographic Conventions 174
- Additional Information Info–5 175
Verwandte Produkte und Handbücher für Messgeräte Altera 10-Gbps Ethernet MAC MegaCore Function
(223 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern