Altera 10-Gbps Ethernet MAC MegaCore Function Bedienungsanleitung Seite 100
- Seite / 175
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8–6 Chapter 8: Registers
MAC Registers
10-Gbps Ethernet MAC MegaCore Function User Guide February 2014 Altera Corporation
0x804
rx_frame_spaddr0_0
RW 0x0 You can specify up to four 6-byte
supplementary addresses:
■
rx_framedecoder_spaddr0_0/1
■
rx_framedecoder_spaddr1_0/1
■
rx_framedecoder_spaddr2_0/1
■
rx_framedecoder_spaddr3_0/1
You must map the supplementary addresses
to the respective registers in the same manner
as the primary MAC address. Refer to the
description of
rx_frame_addr0
and
rx_frame_addr1
.
The IP core uses the supplementary addresses
to filter unicast frames when the following
conditions are set:
■ The use of the supplementary addresses
are enabled using the respective bits in the
rx_frame_control
register (refer to
“Rx_frame_control Register” on
page 8–16).
■ The
en_allucast
bit of the
rx_frame_control
register is set to 0.
0x805
rx_frame_spaddr0_1 (1)
RW 0x0
0x806
rx_frame_spaddr1_0
RW 0x0
0x807
rx_frame_spaddr1_1 (1)
RW 0x0
0x808
rx_frame_spaddr2_0
RW 0x0
0x809
rx_frame_spaddr2_1 (1)
RW 0x0
0x80A
rx_frame_spaddr3_0
RW 0x0
0x80B
rx_frame_spaddr3_1 (1)
RW 0x0
0x818
rx_pfc_control
RW 0x1
PFC enable for the priority queues on the
receive datapath.
Refer to “Rx_pfc_control Register” on
page 8–17 for the bit description.
0x819 –
0xBFF
Reserved — — Reserved for future use.
TX Packet Transfer (0x1000:0x103F)
0x1000
tx_transfer_control
RW 0x0
Backpressure enable.
■ Bit 0 configures transmit transfer control.
0—Enables transmit transfer datapath.
1—Disables transmit transfer datapath on
the Avalon-ST transmit interface. The IP
core deasserts the
avalon_st_tx_ready
signal.
■ Bits 1 to 31 are reserved.
0x1001
tx_transfer_status
RO 0x0
■ Bit 0 indicates if transmit transfer datapath
is enabled on the Avalon-ST transmit
interface.
0—Transmit transfer datapath is enabled.
1—Transmit transfer datapath is disabled.
■ Bits 1 to 31 are reserved.
0x1002 –
0x103F
Reserved — — Reserved for future use.
TX Pad Inserter (0x1040:0x107F)
Table 8–2. MAC Registers (Part 5 of 15)
Word
Offset
Register Name Access
Reset
Value
Description
- User Guide 1
- Contents 3
- Contents iv 4
- Chapter 8. Registers 5
- Chapter 9. Interface Signals 5
- 1. About This IP Core 7
- 1.2. Release Information 8
- 1.3. Device Family Support 9
- 1.4. IP Core Verification 10
- ■ Timestamping is enabled 12
- ■ ptp_1step is disabled 12
- 2.2. Design Flows 14
- 2.3.2. Simulate the IP Core 15
- 2.4.1. Specify Parameters 16
- 2.4.3. Simulate the System 17
- [1] register bit to 1 18
- 3. 10GbE MAC Design Examples 19
- 3.2.0.2. Base Addresses 22
- Table 3–5 on page 3–10 23
- Creating a New 10GbE Design 24
- 3.6. 10GbE Testbenches 26
- 3.6.3. 10GbE Testbench Files 27
- 10GbE Testbenches 28
- Notes to Table 3–6: 36
- 4.1. Software Requirements 39
- Altera FPGA 40
- Design Example 40
- 4.2.1. Base Addresses 41
- Figure 4–3. Testbench 43
- The <ip 44
- Simulator 45
- 5.2.2. Base Addresses 49
- 1G/10GbE Design Example Files 50
- 5.5. 1G/10GbE Testbench 51
- Testbench 52
- 1G/10GbE Testbench 53
- 5.5.4.2. Backplane-KR Mode 55
- 6.2.1. Base Addresses 62
- ModelSim Simulator 66
- 7. Functional Description 68
- Architecture 69
- 7.2. Interfaces 70
- 7.2.2. SDR XGMII 71
- 7.2.3. GMII 71
- 7.2.4. MII 71
- 7.3. Frame Types 72
- 7.4. Transmit Datapath 72
- 7.4.2. Address Insertion 73
- Note to Figure 7–5: 74
- 7.4.4. XGMII Encapsulation 75
- 7.4.6. SDR XGMII Transmission 76
- Figure 7–7. Endian Conversion 77
- 7.5. Receive Datapath 78
- 7.5.4. Address Checking 79
- 7.5.5. Frame Type Checking 79
- 7.5.6. Length Checking 80
- 7.5.7. CRC-32 and Pad Removal 81
- 7.5.8. Overflow Handling 82
- Congestion and Flow Control 83
- 7.7.2.1. PFC Frame Reception 86
- Figure 7–11. Fault Signaling 87
- 7.9. IEEE 1588v2 88
- IEEE 1588v2 89
- 7.9.1. Architecture 90
- 7.9.2. Transmit Datapath 91
- 7.9.3. Receive Datapath 92
- 7.9.4. Frame Format 92
- MAC Header 93
- Note to Figure 7–16: 94
- 8. Registers 95
- 8.1. MAC Registers 96
- 0x0C1. Bits 4 to 31 are 98
- 0x0C3. Bits 4 to 31 are 98
- Register Name Access 100
- Bits 4 to 31 are reserved 101
- register 111
- Name R/W Description 112
- 8.3. Register Initialization 113
- 8–20 Chapter 8: Registers 114
- Register Initialization 114
- Chapter 8: Registers 8–21 115
- 8–22 Chapter 8: Registers 116
- Chapter 8: Registers 8–23 117
- 8–24 Chapter 8: Registers 118
- Chapter 8: Registers 8–25 119
- 9. Interface Signals 120
- Note to Table 9–1: 121
- Note to Figure 9–2: 123
- Note to Figure 9–3: 123
- Notes to Figure 9–4: 124
- Note to Figure 9–5: 125
- 9.0.3. SDR XGMII 127
- Note to Figure 9–7: 128
- Note to Figure 9–8: 129
- 9.0.4. GMII Signals 130
- 9.0.5. MII Signals 130
- Note to Table 9–8: 136
- Note to Table 9–9: 139
- 1588v2 feature 142
- 10. Design Considerations 150
- 10GbE MAC XAUI/10G BASE-R PHY 151
- Reconfiguration Controller 151
- A. Frame Format 153
- Figure A–2. VLAN Frame Format 154
- A.3. Pause Frame 155
- Figure A–5. PFC Frame Format 156
- B. Time-of-Day (ToD) Clock 157
- B.4. Parameter Setting 158
- ■ Bits 20 to 31: Not used 160
- B.6.1. Adjusting ToD’s Drift 161
- C. Packet Classifier 162
- Classifier 163
- D. ToD Synchronizer 166
- D.2. Block Diagram 167
- D.4. ToD Synchronizer Signals 169
- Additional Information 171
- Info–2 Additional Information 172
- Document Revision History 172
- Additional Information Info–3 173
- How to Contact Altera 174
- Typographic Conventions 174
- Additional Information Info–5 175
Verwandte Produkte und Handbücher für Messgeräte Altera 10-Gbps Ethernet MAC MegaCore Function
(223 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern