Altera Arria V Avalon-ST Bedienungsanleitung Seite 70
- Seite / 248
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Signal Directi
on
Description
• cpl_err[4]: Unsupported Request (UR) error for posted TLP.
The Application Layer asserts this signal to treat a posted request
as an Unsupported Request. The Hard IP automatically sets the
error status bits in the Configuration Space register and sends
error messages in accordance with the PCI Express Base Specifica‐
tion. Many cases of Unsupported Requests are detected and
reported internally by the Transaction Layer. For a list of these
cases, refer to Transaction Layer Errors.
• cpl_err[5]: Unsupported Request error for non-posted TLP. The
Application Layer asserts this signal to respond to a non-posted
request with an Request (UR) completion. In this case, the
Application Layer sends a completion packet with the
Unsupported Request status back to the requestor, and asserts this
error signal. The Hard IP automatically sets the error status bits in
the Configuration Space Register and sends error messages in
accordance with the PCI Express Base Specification. Many cases of
Unsupported Requests are detected and reported internally by the
Transaction Layer. For a list of these cases, refer to Transaction
Layer Errors.
• cpl_err[6]: Log header. If header logging is required, this bit
must be set in the every cycle in which any of cpl_err[2], cpl_
err[3], cpl_err[4], or cpl_err[5]is set. The Application Layer
presents the header to the Hard IP by writing the following values
to the following 4 registers using LMI before asserting cpl_
err[6]:. The Application Layer presents the header to the Hard IP
by writing the following values to the following 4 registers using
LMI before asserting cpl_err[6]:
• lmi_addr: 12'h81C, lmi_din: err_desc_func0[127:96]
• lmi_addr: 12'h820, lmi_din: err_desc_func0[95:64]
• lmi_addr: 12'h824, lmi_din: err_desc_func0[63:32]
• lmi_addr: 12'h828, lmi_din: err_desc_func0[31:0]
cpl_pending[7:0]
Input
Completion pending. The Application Layer must assert this signal
when a master block is waiting for completion, for example, when a
transaction is pending. This is a level sensitive input. A bit is provided
for each function, where bit 0 corresponds to function 0, and so on.
cpl_err_func[2:0]
Specifies which function is requesting the cpl_err. Must be asserted
when cpl_err asserts. Due to clock-domain synchronization
circuitry, cpl_err is limited to at most 1 assertion every 8 pld_clk
cycles. Whenever cpl_err is asserted, cpl_err_func[2:0] should be
updated in the same cycle.
2014.12.15
Completion Side Band Signals
4-33
Interfaces and Signal Descriptions
Altera Corporation
Send Feedback
- User Guide 1
- Datasheet 2
- Features 3
- Release Information 5
- Device Family Support 6
- Altera FPGA 7
- Arria V or Cyclone V FPGA 8
- Debug Features 10
- IP Core Verification 11
- Recommended Speed Grades 11
- Qsys Design Flow 15
- Generating the Testbench 17
- Simulating the Example Design 17
- Directory Description 18
- Modifying the Example Design 21
- Parameter Settings 24
- Parameter Value Description 25
- Link Capabilities 27
- Device Capabilities 28
- Error Reporting 30
- Slot Capabilities 31
- Power Management 32
- <n> 34
- Legacy Interrupt 37
- Application Layer 39
- Avalon‑ST RX Interface 39
- Signal Direction Description 40
- Packet TLP 43
- Aligned Addresses 47
- Avalon-ST TX Interface 50
- Clock Signals 61
- Reset Signals 61
- Hard IP Status 63
- Error Signals 66
- ECRC Forwarding 66
- Interrupts for Endpoints 67
- Completion Side Band Signals 68
- Signal Directi 69
- Description 69
- Field and Bit Map 78
- 0134678951 78
- LMI Signals 79
- Hard IP for PCIe 80
- Power Management Signals 82
- 15 011623 8 2791213142431 83
- Bits Field Description 84
- Serial Interface Signals 86
- 9 Ch 18 Ch 87
- Variant Data CMU Clock 88
- PIPE Interface Signals 91
- Test Signals 95
- Registers 100
- Altera Corporation 100
- Send Feedback 100
- 2014.12.15 101
- Altera-Defined VSEC Registers 104
- CvP Registers 105
- Bits Register Description 109
- Reset and Clocks 112
- Example Design 113
- Hard IP for PCI Express 113
- Clock Domains 116
- Data Rate Frequency 117
- Related Information 117
- Clock Summary 118
- Interrupts 119
- Figure 7-1: MSI Handler Block 120
- Allocated 121
- Implementing MSI-X Interrupts 122
- Legacy Interrupts 124
- Interrupts for Root Ports 125
- Error Handling 126
- Physical Layer Errors 127
- Data Link Layer Errors 127
- Transaction Layer Errors 128
- Error Type Description 129
- Status Bit Conditions 132
- IP Core Architecture 134
- Hard IP for PCI Express 135
- Top-Level Interfaces 136
- Avalon-ST Interface 136
- Clocks and Reset 136
- Hard IP Reconfiguration 137
- Transceiver Reconfiguration 137
- Transaction Layer 138
- Configuration Space 139
- Data Link Layer 140
- Physical Layer 142
- TX Packets 143
- Multi-Function Support 144
- Supported Message Types 146
- INTX Messages 146
- Power Management Messages 147
- Error Signaling Messages 148
- Locked Transaction Message 149
- Slot Power Limit Message 149
- Vendor-Defined Messages 149
- Hot Plug Messages 150
- Receive Buffer Reordering 152
- Using Relaxed Ordering 154
- Throughput Optimization 157
- Throughput of Posted Writes 159
- Design Implementation 161
- Making Pin Assignments 162
- Optional Features 163
- ECRC on the RX Path 164
- ECRC on the TX Path 165
- Subscribe 168
- Testbench and Design Example 171
- Root Port Testbench 174
- Chaining DMA Design Examples 174
- Root Complex 176
- Chaining DMA 176
- Hard IP for 176
- PCI Express 176
- BAR/Address Map 179
- Memory BAR Mapping 180
- Bit Field Description 181
- Addr Register Name 181
- Byte Address 184
- Offset to Base 184
- Descriptor Type Description 184
- Bits[21:18] Bit[17] Bit[16] 185
- Descriptor Field Endpoint 185
- RC Access Description 185
- Test Driver Module 186
- DMA Write Cycles 187
- Shared Memory 188
- DMA Read Cycles 189
- Registers (BAR2) 190
- Root Port Design Example 191
- Root Port 192
- Variation 192
- (variation_name.v) 192
- Root Port BFM 193
- BFM Configuration Procedures 194
- BFM Request Interface 194
- BFM Memory Map 195
- Offset (Bytes) Description 197
- BFM Procedures and Functions 201
- Location altpcietb_bfm_rdwr.v 202
- Express address 203
- Shared Memory Constants 210
- Constant Description 211
- Location 216
- Debugging Simulations 228
- Debugging 229
- Setting Up Simulation 232
- Use Third-Party PCIe Analyzer 234
- BIOS Enumeration Issues 234
- Address[31:2] 235
- Figure A-6: I/O Read Request 237
- 7 6 5 4 3 2 1 0 241
- Core Config 8 4 1 241
- Additional Information 243
- Date Version Changes Made 244
- How to Contact Altera 246
- Typographic Conventions 247
- Visual Cue Meaning 248
Verwandte Produkte und Handbücher für Messgeräte Altera Arria V Avalon-ST
Messgeräte Altera DDR3 SDRAM High-Performance Controller and ALTMEMP Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Messgeräte Altera DDR SDRAM High-Performance Controllers and ALTMEMP Bedienungsanleitung
(140 Seiten)
(140 Seiten)
Messgeräte Altera Floating-Point Bedienungsanleitung
(157 Seiten)
(157 Seiten)
Messgeräte Altera JESD204B IP Bedienungsanleitung
(158 Seiten)
(158 Seiten)
Messgeräte Altera Nios II Embedded Evaluation Kit Cyclone III Editio Bedienungsanleitung
(80 Seiten)
(80 Seiten)
Messgeräte Altera SCFIFO Bedienungsanleitung
(28 Seiten)
(28 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern